(TH-6) Automatic Submerged-Arc Welding Machine for Column Circumferential Joints
The automatic submerged-arc horizontal welding machine is a specialized, high-efficiency welding system designed for vertical steel pipe and steel plate horizontal butt joints with deep bevels. It is ideally suited for welding operations on offshore platform risers, pile legs, offshore wind turbine towers, and thick-walled plates.
Key words:
(TH-6) Automatic Submerged-Arc Welding Machine for Column Circumferential Joints
Classification:
Hotline:
Product Details
I. Overview
1. Principle of the Automatic Submerged-Arc Welding Machine for Column Circumferential Joints
Horizontal seam submerged arc welding is a specialized variant of conventional submerged arc automatic welding. It employs a specially designed flux‑feeding device that continuously tracks the weld position along the weld seam. By carefully adjusting the welding current, arc voltage, and welding speed, it achieves proper weld bead formation in the transverse direction.
2. Welding Efficiency
Horizontal seam submerged-arc automatic welding employs a multi-pass, multi-layer welding process, achieving a weld deposition rate 5 to 6 times that of manual arc welding. Taking into account groove geometry, deposition speed, and pure welding time, equipping the operation with two or more horizontal seam submerged-arc automatic welding machines for simultaneous welding maximizes the benefits of automated welding, reduces installation time for wind shields, and eliminates the need for gas shielding.
3. Degree of Welding Automation
The submerged-arc automatic welding control cabinet for transverse seams is positioned on the operator’s right side, with all welding controls centralized on the cabinet. It features an automated flux delivery and recovery system, enabling the flux to be reused automatically. The welding torch offers flexible adjustment, while the traveling carriage is equipped with a brushless motor drive and an automatic wire‑feeding system, ensuring fully automated welding operations.
4. Working Environment: In arc welding, the electric arc burns beneath a layer of flux, with no visible arc light and minimal fumes and dust. The welding process is fully automated; the operator merely monitors the torch’s position, resulting in low physical exertion, a clean working environment, and full suitability for outdoor operations.
5. Scope of Application
The automatic submerged-arc welding machine is a vertical pipe‑plate horizontal butt‑joint deep‑groove welding system, suitable for horizontal butt‑joint welding of offshore platform risers, pile legs, offshore wind turbine towers, and thick‑walled plates. Its structure is based on a T6 riser horizontal welding unit, supplemented with additional components to enable all‑position circumferential submerged‑arc welding. The welding head provides full‑position flux coverage, accommodating pipe diameters of 1200 mm and above, while also delivering high‑quality welds on flat‑plate deep‑groove joints.
6. Equipment Configuration
The complete system comprises a stable and reliable digital inverter submerged-arc power source, a vertical wire‑feeding unit equipped with a high‑power feed motor, a traveling carriage, and a track. The carriage features magnetic adhesion and brushless‑motor drive for smooth movement, along with loading and unloading hoppers, a control box, and quick‑release interconnecting cables. The main welding torch employs a dual‑motor flux‑push feeding system with adjustable flux‑flow settings, enabling it to accommodate diverse welding parameters across different layer thicknesses and supporting wire diameters of φ2.4, 3.2, and 4.0 mm. The weld pool is fully covered by flux, allowing outdoor operations without the need for shielding enclosures or shielding gases, and eliminating arc radiation—thereby enhancing weld quality and production efficiency. Additionally, the unit includes an integrated high‑pressure flux recovery system; a three‑layer flux‑collection tray ensures that more than 95% of spilled flux is recovered and reused, reducing material costs. The electrical control panel offers selectable travel speeds for the carriage, switches for fast/slow flux advance, wire‑feed and wire‑retract functions, and is equipped with low‑voltage illumination and a purge gun. The track utilizes magnetic guidance combined with pine‑cone‑type pulleys and locking devices at joint connections, ensuring secure attachment to the pipe wall and uniform, reliable movement, thus guaranteeing safe operation throughout the welding process.
II. Characteristics
1. The traveling carriage, the upper and lower hoppers, the welding torch mounting, the flux recovery piping, and the control box assembly can all be quickly disassembled; assembly is convenient and requires no tools.
2. The hopper system comprises a main recovery hopper and an auxiliary hopper, each equipped with a transparent observation window for直观ly monitoring the flux‑storage level inside. The auxiliary hopper features an open‑top design, enabling convenient on‑demand replenishment of flux. Both hoppers are fitted with stainless‑steel mesh screens to prevent large particles from entering the flux‑delivery chamber, thereby avoiding blockage of the delivery motor.
3. The carriage is equipped with a clutch mechanism, allowing operators to move it quickly.
4. Welding parameters are displayed digitally, and the control system is synchronized with the welding current settings for simultaneous adjustment.
5. The system employs precise program-controlled travel speed and accurately regulates the flux feed rate, ensuring consistent weld quality.
6. Welding is performed under flux protection, enabling on-site welding operations without the need for wind‑proofing measures.
7. The vehicle is constructed from aluminum alloy and stainless steel, featuring integrated up-and-down adjustment; either of the two handwheels on the left or right can be used to flexibly and synchronously adjust the vehicle’s vertical dimensions.
8. Welding torch support plate: the lower hopper features synchronized up-and-down adjustment, and the vertical distance can be flexibly adjusted using either handwheel.
9. The automatic welding carriage and its track-mounted idler wheels can have their angles adjusted at any time to accommodate different pipe diameters, operating in synchronized motion with the track.
10. The wire feeder features a vertical structural design, equipped with a 300 W DC servo motor operating at 110 V and delivering 3,300 rpm. Weighing 10 kg, it incorporates a four-wheel‑drive wire feeding system and a wire straightening mechanism. The wire feed rollers are housed in a sealed compartment, while the wire spool is vertically mounted at a safe distance from the base. It offers both wire feeding and wire retracting functions. Dual handles on either side of the upright column ensure easy handling, and the unit’s lightweight construction is complemented by four swivel casters with brakes, providing convenient mobility and transport.
11. The welding power source employs microcontroller and CPLD control technology, enabling digital control of the welding process, enhancing control accuracy, and reducing the failure rate. Utilizing IGBT inverter technology, it ensures highly stable welding current even under grid voltage fluctuations and changes in arc length, with strong arc self‑regulation and a high arc‑start success rate. It offers both flat and declining output characteristics, accommodating wire diameters from 1.6 to 6.0 mm and providing a wide current adjustment range. Lightweight and compact, it is easy to transport.
12. The uniquely designed welding torch can extend into weld seams deeper than 60 mm, ensuring optimal wire protection and superior weld quality. Its 60° vertical adjustment allows for precise angle control when filling and capping large groove preparations. Flux is fed from the hopper into the flux‑delivery chambers on both sides and then propelled by motors to the designated position along the weld bead. Two independent motors deliver flux to the central torch via a helical feeding mechanism, enabling real-time adjustment of flux flow to maintain consistent weld quality across different bead locations. The torch’s fore-and-aft position can be manually adjusted at any time, ensuring straight‑line travel along the weld during operation. Laser alignment indicators mounted on either side of the torch keep the wire at the same horizontal plane, guaranteeing uniform weld height. Both the vertical tilt and the fore-and-aft positioning of the torch are flexibly controlled via handles and gear mechanisms, with locking devices provided for secure settings. A sliding rail system is installed at the retractable position of the torch, facilitating easy adjustments, nozzle changes, and fine‑tuning of the standoff distance between the torch and the weld bead during operation.
III. Operating Conditions
1. Suitable for pipes with diameters of 1200 mm or greater, as well as for horizontal, straight welds in deep groove preparations with thick wall thicknesses. It is ideal for wall thicknesses ranging from 10 to 65 mm, with groove angles of 30° at the top and 15° at the bottom, or a combined upper-and-lower angle of 30°, and for welding thick‑walled plates.
2. The root gap of the weld shall be uniform and not exceed 2 mm; otherwise, weld quality will be compromised.
3. Suitable for solid-core submerged-arc welding wires with diameters of φ2.4, φ3.2, and φ4.0 or less.
IV. Specifications and Technical Parameters
Power Supply Parameters
| Power supply voltage/frequency | Three-phase 380 V ±10% / 50 Hz |
| Rated Input Capacity (kVA) | 55 |
| Rated Input Current (A) | 83 |
| Rated duty cycle | 100% |
| Output current adjustment range (A) | 60–1000 |
| Output Voltage Regulation Range (V) | 20–50 |
| Output no-load voltage (V) | 84 |
| Using welding wire diameter (mm) | 1.6–5 |
| Welder weight (kg) | 95 |
| Welder volume (cm³) | 77×35×77 |
| Insulation Class | H |
| Minimum power supply capacity | 78 Power Grid (kVA) |
| 120 kVA generator | |
| Input Protection | 90 fuse (A) |
| 120 Circuit Breaker (A) | |
| Cable | ≥16 Input side (mm²) |
| 70×2 Output side (mm²) | |
| 16 Grounding conductor (mm²) |
Vehicle parameters
| Applicable workpiece | All pipe diameters 1200 mm and above |
| Gait | Dual‑adsorption magnets (for the cart body and the flux recovery box), flexible track |
| Drive method | Four-wheel drive (aluminum alloy wheels) |
| Clamping force | Overall track weight: 200 kg |
| Forming method | Stainless steel soft rail guide |
| Walking speed | 3.5 — 90.0 (cm/min) |
| Solder flux spreading device speed | 3.5 — 90.0 (cm/min) automatically synchronized with walking speed |
| Input compressed air pressure | 0.6mpa-0.8mpa |
| Applicable welding wire | 2.4mm-4.0mm |
| Welding torch adjustment method | Front and rear pull‑out straps with locking mechanism, with 60° angle adjustment up and down. |
| Main material | All-aluminum body, with stainless steel hopper and discharge chute. |
| Car dimensions | Length × Width × Height |
| Weight | 26 kg (including the traveling carriage and the upper and lower flux hoppers) |
| Stainless steel flexible track | Stainless steel snap‑lock fastening; each rail is fitted with six pinecone‑style assist rollers, and three magnetic blocks provide secure adhesion. |
| Track material | Elastic stainless steel |
Air-cooled welding torch parameters
| Welding torch adjustment range | The slider is equipped with a pull‑out mechanism for forward and backward adjustment, and the base features a locking device, allowing the tilt angle to be adjusted by up to 60°. |
| Welding torch rod material | Pure brass |
| Internal configuration of the gun | Short guidewire sheath |
| Material of the welding torch insulating sleeve | Epoxy Insulation Treatment |
| Dual-chamber design | Dual-motor flux‑feeding system with adjustable feed rates, offering a maximum feed speed of 90 rpm. |
Wire Feed Device Parameters
| Motor power | DC servo wire feed motor, 300 W power |
| Voltage | 110V |
| Rotational speed | 3,300 rpm |
| Weight (KG) | 10kg |
| System | Four-wheel drive wire feeding system and welding wire straightening system |
| Wire Feed Roller Design | Acrylic cover plate protecting the wire feed wheel |
| Welding Wire Spool Design | The wire spool features a vertical design and is set at a certain distance from the base. |
| Functionality | It has wire feeding and wire retraction functions. |
| Lifting weight | The dual-handle design on both sides of the column ensures easy handling, with a total weight not exceeding 45 kg. |
| Caster wheel | Equipped with four swivel casters with brakes and wear-resistant wheels, ensuring easy mobility and handling. |
Technical Specifications
| Parameter Name | Parameter range |
| Walking speed | 2.0 cm–90.0 cm/min |
| Shipping speed | 10.0 rpm – 90.0 rpm |
| Welding current* | 50A-900A |
| Welding voltage* | 20.0V-50.0V |
*Welding current and welding voltage vary depending on the selected welding power source model.
Honor
Enterprise style
Previous Page
Next Page
Previous Page
Next Page
Related Products
THG-8 type magnetic suction pipe all-position automatic welding machine
THG-8 type magnetic suction pipe all-position automatic welding machine is the latest product jointly developed by Tianjin Huigong Automation Equipment Co., Ltd., domestic universities and users.
TH-500SS Dual-Wire Gas-Shielded Welding
The TH-500SS carrier‑controlled dual‑wire CO₂ gas‑shielded arc welding machine is a new, high‑efficiency dual‑wire welding power source developed by our company through the integration of domestic and international technologies. Its uniquely designed dual‑wire wire‑feeding mechanism ensures lightweight, effortless operation with an air‑cooled torch. Compact in size and light in weight, it is easy to transport.
(TH-6) Automatic Submerged-Arc Welding Machine for Column Circumferential Joints
The automatic submerged-arc horizontal welding machine is a specialized, high-efficiency welding system designed for vertical steel pipe and steel plate horizontal butt joints with deep bevels. It is ideally suited for welding operations on offshore platform risers, pile legs, offshore wind turbine towers, and thick-walled plates.
Customer Message
We will contact you within one working day. Please pay attention to your email.









